Instant water heater easy to install requires 13A power supply!
This 3kW instantaneous water heater is very energy efficient since they only consume energy when they are being used. The Ultrawash is suitable for standard 15mm pipe fittings using 1/2” BSP female adapters. This water heater will run on a minimum cold water pressure of just 0.25Bar this is equal to (3.626 PSI). The maximum cold water inlet pressure should not exceed 10Bar this is equal to (145.038PSI). The Ultrawash is very easy to install they incorporate a 180 Ø spray arm.
No expansion kit required with this instantaneous water heater, low cost, simple to install this unit incorporates a pressure relief valve and requires just 0.25bar water pressure to operate!
Assembled and pre-tested here in the UK!
Very energy efficient since they only consume energy when they are used
Requires standard 15mm pipe fittings using 1/2"BSP female adapters
The Ultra-wash is an open outlet continuous flow water heater
White plastic outer case
Safety thermal cut-out
180 Swivel spray-head
Spout length: 200mm
Integral inlet tap
W164mm: D77mm: H210mm
Boxed weight 1.4kg
Min (P) Bar
Max (P) Bar
The temperature of the outlet water depends on the flow rate an the inlet water temperature, see table below: UL30E APPROXIMATE TEMPERATURE RISE FROM AMBIENT WATER INLET TEMPERATURE C
What is the warranty of the Ultrawash instant water heater?
One year manufacturer’s warranty!
What power supply do I require?
The Ultrawash 3kW can be supplied from a 13amp fused spur point!
Can this water heater be fitted with a plug?
No all instant water heaters must be installed by a competent electrician and for safety reasons they must be hard wired to a suitable power supply.
Do I need any accessories for installation?
No special accessories required for installing the Ultrawash. The Ultrawash does not need any expansion kits and can be installed to the water supply using standard UK 15mm pipe fittings!
What size cable do I need?
The Ultrawash requires a minimum of 1.5mm2!
Will it cope with fluctuating water pressures?
The Ultrawash instant water heaters has an inbuilt water regulator so it will control fluctuating water pressures ranging from 0.25bar up to 10bar if you are unsure of your cold water supply pressure you can ask your water supplier to check this for you free of charge!
Will this water heater work from a water tank supply?
Yes you can use a header tank feed but this would need to give a minimum head pressure of 0.25bar (3.626 psi) this will be achieved with a tank with a minimum head of 7 meters (23ft)!
What temperatures should I expect from this water heater?
With all low powered instant water heaters the temperature of the water delivered to the unit will affect the performance. During the winter months when the water supply is much colder the Ultra washes performance will also be affected as with all 3kW instant water heaters. The temperature delivered by this water heater during the summer months will be 21C to 38C and in the winter months this will be reduced!
How will it cope with hard water areas?
The majority of water heater are designed to try an eliminate lime scale build up as much as possible; the Ultrawash is supplied with a water filter that should be fitted on the cold inlet side to the water heater. The Ultrawash also has a removable spray nozzle to enable descaling and cleaning!
Do you have spare parts for the Ultrawash?
Yes we carry spares for the Ultrawash instant water heaters, mainly the spray nozzles and the control knob, if we do not stock the part you require we can get it for you please call our sales team on 08448842900 for any enquiries!
What pipe fittings do I need for the Ultrawash?
The pipe fittings are standard UK 15mm (½” BSP) pipe fittings!
What height should it be installed above the sink?
We would recommend that the bottom of the Ultrawash should be 200mm (7.8”) up from the basin or sink level!
Can it be installed in an outbuilding that is not heated?
We do not recommend that the water heater is installed in a room where it may be subject to freezing!
How far from will the spray arm protrude?
The Ultrawash arm will protrude 200mm (8”) from the wall!
If I have a problem with the Ultrawash who do I contact?
Hyco the manufacturers have a customer help line given within the hand book, or please call our customer services team on 0844 884 2900 and we will help you with any problems you may have with the Ultrawash instant water heater!
Customer Review For Ultrawash 3kW Handwash Open Outlet
Post by Ann Clary
You rated : 4.3 / 5
What amazing service
Post by Richard Edwards
You rated : 4.3 / 5
Thank you for your assistance and I can confirm that the products have now been picked up.
Your end of the supply process was excellent.
Post by Ron Smith
You rated : 4.3 / 5
Many thanks for the brilliant service given regarding the water heater i ordered. arrived yesterday 1/2/2010. will be in touch when anything else is needed.