Find out more about Zip HydroTap All In One Boiling Residential System
Zip HydroTap All In One Boiling Residential System
Zip HydroTap all In One boiling, Chilled, Fittered, hot & cold from one tap Power-Pulse energy saving technology reduces power consumption by allowing the system
to electronically regulate its power during high and low usage periods. This saves energy whilst
maintaining the tightest possible temperature control.
Programmable 24/7 Timer
Pre-set the “power on” and “power off” times (once each day) for those periods when the
HydroTap will not be used such as overnight or at weekends.
Inactivity Sleep Mode
The boiling system can be pre-set to power down after 2 hours of non-use but will still retain
stored “boiling” water at an energy-saving 64ºC. Typical system daily running costs less than
13p with sleep mode active for 10 hours.
Low light Sleep Mode
An integral light detector can be set to automatically activate sleep mode (as above) when room
lights are switched off, returning to normal operation when the lighting is switched back on.
When activated allows the entire system to totally power down after 2 hours of non-use.
Easy reactivation from all four of these modes by pressing the boiling or chilled levers.
Superior sub-micron filtration ensures crystal clear, great tasting, healthier water.
Removes suspended impurities smaller than one thousandth of a millimetre.
Removes chlorine plus other tastes and odours.
Use in place of mixer taps to de-clutter and simplify kitchen design.
For use with all standard domestic hot water systems.
Top mounted drinking water controls for convenience and safety.
Press the red (boiling) or blue (chilled) levers to fill cups or glasses.
Pull levers forward for hands-free measured delivery into larger vessels.
Child safety lock, requiring adult finger-thumb operation, can be activated if required to
control boiling water delivery.
Additional electronic boiling water isolation safety feature also provided.
Separate control lever to dispense hot, cold or mixed warm water.
Superior energy saving features
Boiling chamber 1.8 Ltr, Chilling chamber 1.8 Ltr, Total rating 1.8 KW.
Open outlet boiling system delivers:
Boiling water factory set at 98ºC and
adjustable from 68°C – 99°C.
Chilled water factory set from 7ºC – 11ºC
and adjustable up to 14º C.
Fan cooled condenser chilling system
using R134A refrigerant.
High quality copper tanks.
Long reach tap spout swings 120º for
Tap LEDs indicate system status,
temperature and filter replacement.
Base unit display aids set up and provides
detailed system information.
The Zip HydroTap All-in-One Residential System
is designed to service one or two sinks.
Requires a 50mm hole for tap installation, 15mm mains water supply with isolating valve ready for connection to Zip equipment (within 1 meter) which is easily accessible, Double pole 13 amp fuse spur (in accordance with current wiring regulations) is installed by others and ready for use, Suitable drainage to waste if required ( within 1 metre ) ( Tundish wherever possible ), Suitable fixing point for product, Make sure sufficient space with clearance on wall or within cupboard for product, Confirmation of adequate clearance.
The Zip HydroTap All-in-One Residential System
is designed to service one or two sinks.
Requires a 50mm hole for tap installation.
Should be installed by a competent person
in accordance with the fitting instructions
supplied and UK Water Regulations.
Water supply must be potable (drinkable)
with a minimum pressure of 0.7 bar.
If pressure exceeds 7 bar a pressure limiting
valve must be fitted. The under sink system
must be located within 1 metre of the tap.
Under sink connection tubing to the tap must
be taut for proper drainage and never be
looped or coiled. An isolating valve should be
installed between the supplies and the system.
Should be installed by a competent person in
accordance with the fitting instructions
supplied and UK Electrical Regulations.
System should be connected to a convenient
13A plug or fused spur.
Power supply 220V to 240V AC 50 Hz,
IMPORTANT. It is essential that the cupboard
containing the undersink unit is adequately
ventilated as poor circulation will adversely
affect the performance of the HydroTap. Cupboard doors must be offset all round
using the 4mm buffers provided.
The under-sink system must be installed with
service access clearances of 50 mm left and
right, 220 mm above and 65 mm rear.
Integral sub-micron filter easily accessible for
replacement. Note that use of this filter in
locations with excessively high levels of
sediment in the water supply may significantly
reduce filter life. In such situations a 5 micron
filter may be substituted.
In hard water areas where mineral scale
accumulation is an issue consideration should
be given to the maintenance required. We
recommend the use of the Zip Professional
FL1100 scale filtration system.
Please call for more imformation!
Customer Review For Zip HydroTap All In One Boiling Residential System
What type of water heater is best for a house/ flat/ bed sit?
If you require an electric water heater to serve a residential property we would generally recommend a storage type water heater. Storage type water heaters hold a specific volume of water at a suitable temperature available for you to use while ever the heater is switched on. As you draw water off, the heater tops itself back up and brings the water back to temperature again. These types of water heater are available in a range of different sizes. In order to serve all of the hot water outlets in a residential property, you would generally require 80L- 100L of water. Different manufacturers make storage type water heaters and all of the dimensions and technical information is listed on the individual product descriptions. For details of our current range of storage type water heaters, please click on the link below.
What type of heater is best for a hand washbasin?
There are several different choices available for hand washbasins. You may choose to go for a small storage type water heater- these are available in both under sink and over sink models. Choosing a storage type water heater will guarantee you a specific volume of water at a suitable temperature whilst the heater is switched on. If however you are likely to run off the whole contents of the water heater at once, you would have to wait while the heater filled itself back up and re-heated for more hot water.
Another option for hand washbasins are instant water heaters. Instant water heaters do not store water; they simply heat the water as it passes through the heater. This type of water heater can save on running costs as they only use electricity when the hot water is required. Instant water heaters are available in a range of kW ratings, and the general rule of thumb is that the more powerful the water heater is, the better ‘flow-rate’ and the more consistent performance you will get. Instant water heaters can be a good option if you have a washroom that is used heavily over a short time, i.e. at staff lunch breaks where a small storage water heater might run out of hot water.
What type of water heater is best for providing hot water for washing up?
An average kitchen sink will usually take between 10L and 15L of water to fill it up so we would generally lean towards a storage type of water heater. This type of water heater allows you to store a particular volume of water at a suitable temperature (some heaters have thermostats on the front to allow you to specify a temperature) that can be delivered quite quickly. You could choose to have an instant water heater, but to get the water to a similar temperature you would need to choose one of the more powerful models, and the water would probably run slower out of the instant type models.
What is the difference between vented and un-vented water heaters?
When deciding which type of water heater to use for your bath, sink or hand wash basin it is important to understand the difference between vented and un vented.
An unvented water heater has a water cylinder that stores hot water and delivers it at mains pressure. Unvented water heaters do not rely on gravity for the supply of hot water so they can be installed virtually anywhere under or over sink, cupboard space. The main advantage is that you can get a power shower hot water supply without the expensive and noise of a power pump. The bath, sink or hand basin fills faster and smaller bore pipe-work can be used. This also means you don't have gallons of cold water stood in the loft space merrily producing bacteria for you to bath in. Unvented water heaters can also be used with standard, mixer and auto sensor taps. The disadvantages of unvented water heaters is that it can be a BOMB if not installed correctly and for this reason all installers of unvented cylinders MUST be registered for such work. To accommodate for the expansion of water which occurs when the water is heated in the cylinder, a diaphragm pressure vessel should be used on the cold feed water supply connection seek professional advice. Requires mains pressure to work efficiently and if you lose the mains water supply then you have no back up!
Vented water heaters are designed to vent the expansion naturally through special vented taps or through the main hot water supply spout. If the water heater is classed as being vented, then it can be either an under or over sink water heater. The under sink water heater will need special vented taps for it to work safely. The over sink water heaters are usually pre-fitted with a swivel spout. If the vented water heater is an over sink unit then it will have a spout supplied at the front, this means the expanded water will vent via the special taps or spout. The advantages of this type of water heater are that there is no need for a diaphragm pressure vessel fitting in the cold water pipe-work. They are energy efficient and very reliable water heaters that generally have longer warranties with them. The disadvantages are that special expensive taps may be required if the unit is for under-sink use. Requires mains pressure to work efficiently and if you lose the mains water supply then you have no back up!
Put simply an unvented system is one that is NOT vented to the atmosphere, and a vented system is one that IS
Will I be able to install the water heater myself?
Water heaters do differ in their complexity. Some of the catering water heaters do not need any installation at all, you simply plug them in and stand them on the counter top, while some of the un-vented water heaters require installation by qualified plumbers with a special licence, so it is difficult to answer yes or no. As a general rule, if you are unfamiliar with the product and are not qualified to install the product, we would advise you to seek professional advice.
Will I need any accessories with my water heater?
Some water heaters have optional accessories, which may or may not be required, depending on how you are installing the heaters. All of the water heaters on CNM Online Ltd have ‘technical information’ downloads explaining how the water heaters are to be installed. Some water heaters will require special vented taps, and others will require expansion vessels so it is important that you read through the technical information beforehand. If you are not a qualified plumber, or if you are not sure about what it is that you need, we would advise you to print off the information and consult the qualified person you will be using to install your water heater. Alternatively, you can click here
to contact our support team and we can try and find out more information for you.
What happens if I have a problem with my water heater?
If your water heater develops a fault within the warranty period it is usually best to contact the manufacturer, as some are able to arrange for service engineers to visit you and look at the heater. All manufacturers operate differently, but they will be the best people to advise you how to proceed. Please visit our Faulty Item
section for more information.
No Product Tags.